Leaderboard

And bringing it up to the present state of play... To balance the purple of the headstock and fretboard, I added a slice of purpleheart to a cut block of ebony and carved the beginnings of the bridge. I also cut the fretboard end to where it will meet the soundhole: Next, I turned my attention to the decoration around the soundhole. Although you have to be a bit canny to maintain the accuracy, I actually find the Dremel radius accessory reasonable for this job: I used a 1mm bit to cut a circle at the centre and wrapped some 1mm b/w/b purfling into it after running a teeny bead of glue onto the bottom edge. After scraping the excess purfling off, I drilled an offset radius tool spike-hole that will be used to put in a second, larger offsett ring (you can just see the pencil check marking offset and outside the installed ring): And then another radius tool spike-hole in between those two to be able to cut - using a 3mm bit - a mid radius to create an offset channel for some curved abelone that, all being well, would fit in between the two other rings. It worked!! And finally, the radius tool spike back to the original hole, but at a slightly smaller radius to now cut right through and create the sound hole : And that's how far I've got so far. It's dinky, isn't it!!!! : Next job is the bracing and 25 foot radiusing of the top. Other pesky distractions mean that it is likely to be into next week before I get to that - but when I do, I'll be sure to post the progress

Thanks folks! For the fretboard, I had found an offcut of some purpleheart that I used for neck splices in the past. I sliced a length off on the bandsaw and radiussed it with a radius block: Then used a 24.75" (I think it was) scale in my fretting mitre jig starting at the 5th fret to give me the 17" scale: Next I added some sawn strips of purpleheart to act as binding, curved to radius and taper using my little block plane: As the purpleheart gets exposed to the light it will pinken markedly. Originally, I was going to put a plain ebony headstock plate over the mahogany...but maybe a bit of purpleheart there too? Got me thinking and experimenting. Hmmm...and was there room for a swift in there too? : Then add some dots and frets to the fretboard - this might work: Then back to the neck. No trussrod needed but, as it is a mahogany neck, maybe a little extra stiffness would not go amiss - so I slotted the top for a couple of hollow carbon-fibre beams: With that sorted, I could bandsaw the neck and start shaping that. Before shaping the heel, I added an extension to its length. The neck is just laid on top of the fretboard - it won't be glued on until the neck angle is fully sorted (a long time yet!): Did a bit more carving to start sorting the neck profile and, in the same way that you can't have too many clamps, you can never have too many swifts! You can tell the age of my iphone by the colour aberrations of its camera!! Starting to look like an acoustic guitar neck

I ordered a tenor ukulele mould from Radius Dish UK - superb product but did take a long time to arrive: I also ordered a sitka spruce bookmatched pair, which I planed and scraped down to a touch under 3mm and joined: And also found in my small wood collection a full mahogany back and sides set - I have NO idea when and what I bought that for...but it would do nicely. Again, planed and scraped the sides down, this time to around 2mm and then out came the bending hot pipe. First a good dousing with water: Then on with the leather work gloves. With a bending iron, a hot pipe and a lot of patience plus plenty of spritzing is the key: And before too long, both halves done Once that was fully dry (overnight) I could cut the sides flush at either end and cut a mahogany tail block and neck block to glue them up: Then, having found the rubber-banded clothes pegs in a long-forgotten drawer, applied the kerfed (slotted) linings: And then that's the sides done ready for radius sanding :

Wow, looking amazing!!